In: Products, Resources 25 Jul 2017 Tags: , , , , , , , , , , , , , ,

ATDI announces an innovative method to build digital terrain dedicated to propagation of electromagnetic waves.

How to improve the quality of radio planning:

Actual medium resolution clutter data dedicated to radio planning are based on classification (Dense urban, Suburban, Village, Building blocks, forest, hydro…). With this type of datasets, deterministic propagation models give acceptable results compared to measurements, however, a lot of measurement points cannot be correlated (even with tuning), due to the lack of accurate digital terrain and clutter information (heights and locations of the obstacles, open areas…).

This is why we have developed an innovative method to build more accurate DTM and clutter layers that can be used to create Medium Resolution (10m-20m) and High Resolution datasets (1m-5m).

Different free and commercial sources are combined to create more accurate layers at reduced costs compared to standard datasets.

 

In our example below, on a Medium Resolution dataset (20m)we extracted uncorrelated points from mobile measurement survey, then we performed fixed measurements on these points and built an innovative DTM/Clutter/Building dataset from open data to get better measures/predictions correlation results.

We have used Deygout 1994 / Fine-E propagation model in ICS telecom EV.

Dataset resolution: 20 m.

Test transmitter: 50 W / 138 MHz.

 

Standard Clutter (landcover) model (urban and vegetation contours):

New clutter layer built from Clutter/Building extraction model (Dataset made with ICS telecom EV and ICS map server):

Above, we can see a more realistic urban repartition (in red) than Standard Clutter model.

Building elevations are extracted and medium and high vegetation areas are classified.

Linear (roads, railways, waterways) are added to delineate urban blocks.

Processing time:

< 2 minutes (22 000 km²)

 

Coverage calculation result comparison

Above: Coverage calculation performed on Standard Clutter model

Above: Coverage calculation performed on New Clutter model. We can see a more realistic impact of urban blocks (West), and vegetation (East)

 

Correlation results (originally uncorrelated points only @20 m):

Clutter method Standard deviation Average error Correlation factor
Standard classification 6.78 dB -1.54 dB 0.72
Building extraction 3.81 dB 1.62 dB 0.92
Building extraction + Linear 3.79 dB 1.73 dB 0.92
Buildings transformed to 5 Clutter classes 3.83 dB 1.73 dB 0.92

 

This new method improves significantly the quality of simulations, especially in urban areas. It’s free for Medium resolution datasets and at very affordable price for High Resolution datasets.

We, at ATDI, continue to improve this method. Objectives:

  • Reduce radio planning costs
  • Get always more accurate results
  • Produce data faster

 

Cost:

Resolution Price in Euro
2 m 150 €/km²
5 m 40 €/km²
10 m 5 €/km²
Medium Resolution 0 €/km²

 

ATDI is now building a new China dataset. Will be available soon: www.atdi.com/cartography

 

Thanks to: Japan Aerospace Exploration Agency, National Geomatics Center of China, U.S Geological Survey, Open Street Map, Malta Communications Authority, DianZhen.

In: Resources, Webinars 04 Jul 2017 Tags: , ,

Nearly three decades of development has resulted in the release of Europe’s leading radio planning and modelling software.

ICS telecom EV will be launched to an audience of professionals on 13 July to an online webinar. This session sees the release of the new product and will demonstrate the new and improved features through live demonstrations, enabling users to ask questions to the presenting engineer in ‘real-time’.

ICS telecom EV is an evolutionary change to the software and is available for release to new and existing customers from 13 July. For full details of the release and upgrade route for existing users please contact your local office.

Date: 13 July 2017
Time: 10am BST
Venue: Online webinar

Space is limited. Reserve your Webinar seat today: Register

ATDI Ltd technical director, Nick Kirkman, says, “The world has changed a great deal over the last three decades and ICS telecom EV is the latest software revolution from ATDI. ICS telecom EV has evolved as a result of market demand, and we now have an accurate, adaptable and versatile solutions for all existing and future radio technologies. This latest release combines the most up-to-date new and improved features ensuring our software adds value now and well into the future for our customers.”

Delegates will receive confirmation on approval of registration.

 

Also please Tweet using this text (plus attached image):

 

Join ATDI ICS Masterclass for the latest product release #software #icstelecomEV
Register

 

 

In: Products, Resources 15 May 2017 Tags: , , , , , , , ,

Efficiently planning mesh networks with HTZ (Part 1 – Digital cartography).

This post is intended to help a radio-planner, technical director, project manager, or consultant to be more aware of the important goals to pursue when planning large scale mesh networks in urban environments. It proposes innovative ways to accurately manage large areas of interest, using cartographic data with mixed high and medium resolutions.

MeshH1

The radio-planning of mesh networks can be divided into three main topics: – Dimensioning the mesh node distribution in order to achieve the requirement of coverage of the end user. – Analyzing the linkage of the Mesh Nodes, in order to optimize the dynamic routing and therefore ensuring demand throughput. – Backhauling the gateways (Microwave links…).

  • Required components
    Cartographic data Mesh network planning can be achieved by using different kinds of digital cartography. The choice depends on the data already available, the budget to be spent, the time available for the planning and the accuracy to reach. The user usually is able make the choice between two types of datasets: – Medium Resolution cartography – High Resolution cartography giving exact locations and heights of the buildings for a given area of interest. However, both datasets have their pros and cons because the areas to treat during mesh planning are large. A third dataset choice known as a hybrid dataset, combines the advantages of both other types of cartography and will be highlighted throughout this document.

 

Medium Resolution for large areas (From 10 to 30 m resolution)
A typical medium cartographic dataset contains the following layers:

– A Digital Terrain Model

– A clutter file, provides a description of the ground occupancy as major aggregates (urban, dense urban…)

– Topographic or Aerial maps (Online or Offline)

MeshH2

Adapting the medium cartography to mesh planning Standard Medium Resolution datasets usually do not feature the roads, because their width is usually smaller than the resolution of the dataset itself. Roads and streets are a crucial component for mesh radio-planning.  The mesh nodes are usually installed in the streets in order to take advantage of the canyoning effect. If the roads and the streets are not available, HTZ features a drawing interface allowing the radioplanners to add the streets in clutter file by importing the street network from a GIS database (OSM, National Geoportal, GIS collections…)

MeshH3

Pros and Cons

The Medium Resolution dataset for mesh planning offers several advantages:

– It allows the treatment of very large areas: the planning of an entire large city can easily be achieved

– The availability of this data is quite good, usually for a reasonable cost

– The resolution of the data allows very fast computations

– Prediction values can be compared with mobile measurement data

However, the radio-planner has to keep in mind that a reduced resolution for the cartography usually generates a reduction in the planning accuracy. Because of the sensitivity to the building environment of the mesh frequency (usually in the ISM bands), using a coarse cartography will generate a coarse planning result that might not reflect the planning accuracy that is targeted (especially for the “hot-zone(s)). Also, the cartography must be manually treated in order to “dig” the streets in the dataset (if the data is not already available in GIS format), in order to provide the ability to simulate the canyoning effect between the mesh nodes.
MeshH4

Availilbity: Worldwide (<=30 m)

Planning accuracy (standard deviation):

– HTZ (Deygout94 propagation model): <=5 dB

– Empirical propagation models (3GPP / Seamcat / Cost): <=8 dB

– Half determinitistic models (ITU / FCC): <= 7 dB

– Coordination models (ITU / HCM): <= 10 dB

Cost-effectivness (Dataset building workload): < 2 days (depends on surface and resolution)

Vintage dependency (Free Clutter data): between 5 and 10 years old

 

High Resolution (from 1 m to 5 m)

A typical high resolution cartographic dataset contains the following layers:

– A high resolution Digital Terrain Model (featuring the bridges for instance)

– A building height file, for the canyoning effect and for building diffusion loss

– A clutter file that describes the vegetation and the different “types” of buildings (concrete, glass…)

– Ortho-photos or Aerials

MeshH5

Pros and Cons

High Resolution cartographic data provides precise building location and height for a specified area of interest. It is the optimal product to achieve excellent planning accuracy in outdoor (canyoning effect according to the exact shape of the buildings) and also in indoor (signal diffusion according to the building type) environments, even though it might require longer computation time.

– Prediction values cannot be compared with mobile measurement data (only fixed measurement data)

However, this type of data remains expensive. It is therefore advised to be used on small areas, and centred, for instance, on “hot-zone(s)”. The coverage calculated also depends on the building data available: the vintage of the production source is also quite important.

MeshH6

Availilbity: low but can be built on demand (around 150 EUR/km²). Some geographical institutes offer HR data for free or at a very attractive price (< 20 EUR/km²)

Planning accuracy (standard deviation):

– HTZ (Deygout94 propagation model): <=4 dB

– Empirical propagation models (3GPP / Seamcat / Cost): <=8 dB

– Half determinitistic models (ITU / FCC): <= 6 dB

– Coordination models (ITU / HCM): <= 10 dB

 

Hybrid cartographic dataset

Another option in preparing a workspace for the planning of a WiFi mesh network would be a hybrid cartographic dataset. The hybrid dataset uses medium resolution data for the areas where a high degree of simulation accuracy is not critical. The hybrid dataset uses high resolution data for “hotspots” within the user’s planning workspace to optimize simulation accuracy for critical areas. High resolution data includes exact building dimensions centred over these “hotspots.”

The hybrid dataset contains both medium and high resolution layers of cartographic information:

– The DTM covering the entire Area Of Interest, with more details in the hot-zone

– A Clutter file mixing the Medium Resolution data and some High Resolution data

– A building height layer covering the High Resolution areas only (the urban heights in the Medium Resolution are managed in the clutter file)

– Imagery (Online or Offline)

– Vector layer (3D building polygons, transportation…)

MeshH5

MeshH9

Pros and Cons

The hybrid dataset combines the assets of the two datasets previously defined. For most areas, coarse radioplanning is performed with both time and cost effectiveness, whereas the “hot-zones” can be locally analyzed with high planning accuracy. The clutter file requires a careful configuration, because it mixes medium and high resolution data:

– The medium resolution clutter codes are configured with average heights, that will be used by the NLOS (diffraction) engine of HTZ when the final receiver is located inside these clutter codes (Suburban for instance)

– The high resolution clutter codes are configured with no heights (as they are defined in the building height file), but with a diffusion loss coefficient in dB/km. This will be used when the final receiver will be located in a building in a “hot-zone”.

MeshH10

 

Lidar

High Resolution Terrain & Clutter Datasets: Why Lidar?
There are myriad methods, techniques and technologies for obtaining elevation and earth cover information through propagated signals. Those technologies may be based on sound, radio and light and also vary in resolution, difficulty, expense and process. Overall, most of these sensing technologies are based on the time delay of a reflected or scattered signal, though traditional passive sensors can also be used and rely on natural radiation.
Lidar systems illuminate a target with lasers, then receive and process the reflected and/or scattered signal. Modern Lidar systems are compact, precise, and efficient and provide many advantages over traditional photo-based techniques. They allow for sub-1 meter data collection and improvements in post-processing aid in the ease of use of the data. Most post-processed Lidar data is classified by return number and category, further shortening the conversion process from raw data to datasets that are usable in RF propagation tools.
Another advantage of Lidar data collection is that the data may be collected both day and night unlike traditional methods which require collection during daylight. Lidar not only offers high accuracy, but allows for the collection of elevation information in areas of dense vegetation. Since a Lidar pulse can have multiple reflections, it will reveal both surface elevation and terrain elevation at any point. Most other collection techniques only gather information about surface heights. Furthermore, modern Lidar data collection systems are compact and are easily mounted onto light aircraft for data collection over large areas.

Get Lidar Data
Lidar, or light detection and ranging, can be used to quantize terrain, ground clutter and ground occupancy. Airborne Lidar systems are typically used for the purposes of scanning large areas and are composed of a laser and a rotating mirror that is used to sweep the area of interest. The airborne Lidar system then acquires data points by bouncing a laser signal off of the earth, buildings and vegetation. As the airplane flies, the Lidar system quantizes the terrain and ground clutter below in a zigzag pattern, as pictured below.

LidarSensor

The acquired data points are reflections of the laser signal from obstacles in its path, and there may often be multiple reflections of a single emitted signal. One reflection may be produced by buildings, the ground and other solid objects. Trees and vegetation may produce several reflections as the laser signal propagates through the leaves and reflects off of branches and ultimately the ground. Thus, it is common to have multiple returns for a given transmission.
To compute the distances between the airborne Lidar sensor and the reflection point and thus the elevation of the reflection point, calculations are run using the elapsed time and the speed of light. This data is correlated with the GPS positioning of the aircraft along with inertia sensors or gyroscopes to accurately create the environment of three dimensional points that are a Lidar dataset.

Lidar Data Format
Lidar information is typically obtained and stored in ASPRS LAS format. Not only does the LAS format contain information about surface heights, but it also provides header information that contains technical information such as return number, classification, and scan angle, among others. The user may then employ or develop software that sorts through the Lidar data (often in the realm of Gigabytes of data) to create the desired datasets based on required criteria, such as return number or classification.
Once the Lidar data has been sorted as desired, the data can then be manipulated as necessary. In most cases, this involves interpolation of the dataset to create a continuous model without non-return pixels. Lidar data is, by nature, discontinuous since individual measurements are based on specific geographic points. These points are then stored in the LAS file. In essence, a LAS file is a list of measurement information per geographic point. In Figure 2 the image on the left shows a dataset where only the first return is shown.  Any areas in black are points where Lidar data was not obtained during the measurement campaign.  In the image on the right, the dataset is interpolated into a continuous dataset that can be used in radio frequency planning and analysis software as a digital surface model.

MeshH11

Lidar Dataset Preparation for RF Analysis

The images in Figure 3 and descriptions that follow show how ground occupancy and clutter are generated using processed Lidar data:
Aerial Image: The first image is an aerial photo of the area of interest, showing the presence of roads, vegetation, buildings and unoccupied ground.
Bare Earth Image: The second image is a bare earth model that was extracted from the ground points of a Lidar dataset and then interpolated into a smooth, continuous dataset. The bare earth model is also known as the DTM, or digital terrain model, since it contains only ground elevations. The DTM is derived from a Lidar dataset by removing all points but those classified as ground points and then interpolating the data to create a continuous dataset.

MeshH12

First Return Image: The third image is a first return model that was extracted and then interpolated into a smooth, continuous dataset. The first return model may also be called a DSM, or digital surface model, since the heights and elevations it contains are the maximum elevations for the ground and any ground clutter at each point. The DSM is derived from a Lidar dataset by removing all returns but the first return and then interpolating the data to create a continuous dataset.
Ground Occupancy Image: The final image is a clutter dataset, obtained by subtracting the heights in the digital terrain model from the heights in the digital surface model, leaving only buildings, vegetation and any other ground clutter within the file.

Areas in black represent a lack of clutter, where the digital elevation model and the digital surface model are equivalent.

 

RF Analysis Using Lidar Data

Once the Lidar data is processed and converted to the appropriate formats, the user may load the datasets into HTZ to run simulations.

The high resolution Lidar dataset provides for highly precise modeling with sharp blockages.

MeshH13

The above image, is a three dimensional visualization of how the sample RF signal is incident upon the exterior of a large building.  The color variation across the building’s facade and stepped roof represents varying power received levels of the RF signal.

The Case for Lidar Datasets

While traditional terrain and surface cover collection techniques and technologies yield resolutions that often range in the tens of meters and can be as accurate as 3 to 5 meters, Lidar allows for sub-1 meter data collection. As a highly precise and detailed terrain and clutter format, Lidar data is well suited for high-resolution RF analysis. Not only is the user presented with unparalleled accuracy for propagation over bare terrain, but also for propagation over and through ground clutter.